Skip to content
Fine parts & injectors · Precision cleaning

Clean injectors and complex parts with ultrasound — no mechanical scrubbing

Ultrasonic cavitation at 28 kHz generates microbubbles that lift deposits from the channels and cavities you cannot reach by hand — it cleans the part on the inside too, without mechanical scrubbing, provided the cleaning liquid can reach the area. Frequency, temperature and detergent are matched to the material and the deposit.

ALPHA AIC
ALPHA AIC
28 kHz
ultrasonic frequency
60–240 L
tank capacity
no scrubbing
no manual brushing or scraping
AISI 316L
stainless ultrasonic chamber

A part with fine channels never gets fully clean with a brush or by hand — the deposit stays exactly where you cannot reach, and wear or scrap returns with every cycle.

For a workshop manager or a quality officer, the pain is the same regardless of industry: a part with complex geometry — an injector, a nozzle, a carburettor, a component with fine channels — never gets fully clean with a brush or by hand. The deposit stays exactly where you cannot reach, and the problem (wear, scrap, failures) returns with every cycle.

And classic methods not only fail to reach the inside — they create new problems. Brushes and abrasives wear the threads and fine surfaces. Aggressive solvents expose the operator to chemicals. And however carefully one works, the result depends on the person and the day, so it varies.

Why scrubbing is not enough for precision parts

A precision part has precisely those zones that matter most — internal channels, orifices, threads, cavities — that no brush ever touches. Manual cleaning treats the outer surface and misses the inside. The result: residual deposit, incorrect injector flow, assembly failures and scrap discovered too late.

What ultrasonic cleaning changes

Ultrasound shifts the problem from how do I scrub better to how do I clean without touching the part. In a bath of solution, high-frequency waves generate millions of microbubbles that implode on the surface of the part — the phenomenon of cavitation. These implosions lift the contaminant from every zone wetted by the solution, including the channels and cavities that scrubbing cannot reach.

For the decision-maker, that means consistent results and less scrap. For the operator, it means placing the parts in a basket, starting the cycle and receiving clean parts — without part-by-part labour. For the process engineer, it means a parameter that can be set and repeated: frequency, power, bath temperature, time.

Why no brushing or scraping is needed

This is the natural technical question. The answer lies in the mechanism: cavitation provides the mechanical cleaning action and works on the layer of contaminant; no brush, scraper or abrasive is needed. The effect on a specific part still depends on the material and parameters; test on a sample first. That is why the method is used precisely where parts are expensive and delicate — fine mechanics, aerospace, medical instruments.

Below you will find the exact parameters, the recommended equipment and what the switch to ultrasound means for scrap, labour and wear. And the clearest proof remains a practical one: we bring one of your parts and clean it in front of you.

Consequences

What manual cleaning of precision parts costs you

  • !Internal channels and cavities that stay dirty no matter how much you scrub
  • !Wear on the part and on the threads from brushes, scrapers and abrasives
  • !Long labour time for each part, one by one
  • !Inconsistent results — depending on the operator and the day
  • !Scrap and failures from remaining deposits (injectors, nozzles, carburettors)
  • !Exposure to aggressive solvents and their vapours

The solution

How ultrasound cleans — through cavitation, not scrubbing

In a bath of solution, the ultrasonic transducers generate high-frequency waves. These create millions of microbubbles that implode on the surface of the part (cavitation) and lift off the contaminant — including from channels, threads and cavities no brush can reach, provided the cleaning liquid can reach the area. No manual brushing or scraping is required: cavitation provides the mechanical cleaning action, and the effect on the part depends on the material and parameters; sensitive parts are tested on a sample first.

ParameterValueRole
Ultrasonic frequency28 kHz (40 kHz optional)Cavitation that cleans micro-channels without abrasion, wherever the liquid can reach
Ultrasonic power750–4000 W (depending on model)Energy for stubborn deposits
Heating power2000–8000 WActivates the solution without attacking the part
Tank capacity60–240 litresFrom individual parts to serial batches
ChamberAISI 316L stainless steelResists aggressive solutions, durable over time
Mode of actioncavitation, no manual brushingNo brushing or scraping; delicate parts are tested on a sample first
  • Cavitation at 28 kHz lifts deposits from channels and cavities you cannot reach by hand, without mechanical scrubbing.
  • Cavitation lifts the contaminant without manual scrubbing — fine parts are cleaned on the inside too, wherever the cleaning liquid reaches; time and frequency are chosen for the material of the part.
  • The ultrasonic chamber is made of AISI 316L stainless steel, resistant to aggressive solutions; the housing is AISI 304.
  • Heating the bath (2000–8000 W, depending on the model) activates the solution to dissolve oils and deposits, without attacking the metal.
  • Tanks from 60 to 240 litres — from individual parts to entire batches, with consistent results.

See it for yourself

Cavitation at work — the part cleaned in seconds

Curățare cu ultrasunete în câteva secunde | Cum funcționează cavitațiaCommentary in Romanian.

Who it is for

The same problem, across several industries

Auto service & injectorsFine mechanics & toolmakingAerospaceElectronic componentsMedical instrumentsFirearms industry

ROI and risk

Consistent results, no scrubbing wear, no part-by-part labour

  • Batch cleaning instead of manual part-by-part labour — at your volume, that means hours recovered
  • Consistent results, independent of operator and day — less scrap and fewer failures
  • No brushes and abrasives — avoid the scrubbing wear on threads and fine surfaces
  • Less operator exposure to solvents and to manual scrubbing
  • No-obligation trial: we bring one of your parts and clean it during the demonstration

Frequently asked questions

What we get asked most

Does ultrasonic cleaning ruin fine parts or threads?+
No manual brushing or scraping is required: cavitation provides the mechanical cleaning action and works on the layer of contaminant, not a brush or a blade. The effect on a specific part depends on the material and parameters, so we test on a sample first. The method is used for delicate parts, threads and precision components, where brushes would cause wear.
How does it clean injectors on the inside, where a brush cannot reach?+
This is exactly the advantage: the cavitation microbubbles penetrate channels, orifices and internal cavities and lift the deposit from the places you cannot reach by hand, provided the cleaning liquid can reach the area. For injectors, nozzles and carburettors, that means cleaning inside the internal channels too, where scrubbing does not reach.
What types of dirt does it remove?+
Oils, greases, soot, carbon deposits, machining residue, polishing residue and oxides. The cleaning solution and bath temperature are chosen according to the contaminant and the part material.
Can I clean several parts at once?+
Yes. With tanks from 60 to 240 litres, you clean entire batches in a single cycle, with consistent results across the whole series — unlike manual cleaning, where the result varies from part to part.
How much does the equipment cost?+
The ALPHA AIC is offered on request, according to the capacity you need (60–240 litres). Purchase, GRENKE leasing and the AUTONOM long-term equipment rental programme are all available. Request a quote and a demonstration for the configuration suited to your application.
In which fields is it used?+
In auto service (injectors, carburettors, engine parts), fine mechanics and toolmaking, aerospace, electronic components, medical instruments and the firearms industry — anywhere complex parts must be cleaned fully, on the inside, without mechanical scrubbing.
25+
years of industrial expertise
2
European trademarks · HD Cleaners® · TIPORA®
GRENKE
equipment leasing
AUTONOM
long-term equipment rental

Show us what needs cleaning.
We'll help you decide what to test first.

Send us a few details, photos or a short video of the application. Within one working day, a technical sales consultant will review it and come back with the next best step — additional questions, a first recommendation or a proposed test.

WhatsApp
Strada Zorilor 16, Miercurea Ciuc
+40 742 446 516info@hdcleaners.ro