Skip to content

Honest guide · 6 technologies

Don’t choose a machine. Choose the physical principle that matches your dirt.

How do you choose the right cleaning technology? Not by comparing brochures, but by answering three questions about your problem. The guide below compares all six technologies honestly — including when each one is NOT the right choice: dry ice is not cheap to run, and steam does not remove rust. No hype, just physics.

Describe your problem

Three questions decide the technology

1

What are you removing?

Grease and microorganisms call for heat. Rust and paint call for ablation or abrasion. Dust in electrical cabinets calls for a dry process. The dirt dictates the physical principle — not the other way round.

2

May the surface get wet — and may it be touched?

Electrical equipment rules out water-based cleaning unless the equipment and procedures explicitly allow it. Moulds and precision parts rule out abrasion. Food zones rule out blasting media and chemical residue. Every constraint crosses technologies off the list.

3

Do you clean in place or in batches?

A line that cannot be dismantled needs cleaning on the spot. Hundreds of small parts need a bath that works alone. Volume and frequency also decide the real operating cost.

Comparison: the 6 technologies side by side

Every row also states what the technology CANNOT do — the column brochures leave out. Full details and parameters follow below.

TechnologyPhysical principleRemovesDoes not remove / limitDry or wetOperating cost
High-temperature dry steamHeat loosens grease and can support hygiene-critical cleaning; the result depends on the temperature actually reached at the surface, the exposure time and the contamination — not on a nominal machine figure.Grease, oils, biofilm, general organic grimeDoes not remove rust, paint or thick corrosion layersLow-water process — the amount of condensate depends on the machine, accessory and surface; no detergent or disinfectant residue in the steam stepLow — water and power (or diesel) only
Dry ice (CO₂)CO₂ pellets at -78.5 °C detach deposits by thermal shock, then sublimate — straight to gas, no water as the cleaning medium and no secondary abrasive medium; the effect on the surface depends on material, contamination and working parameters.Grease, oil, dust, adhesives, soot, production residues — electrical equipment only after a site-specific electrical safety reviewDoes not remove adherent rust; pellets are a real consumable — this is not the cheap methodDry, no water; no secondary blasting medium (sublimes after impact)High — consumable CO₂ pellets plus compressed air (drops if you produce pellets in-house)
Laser cleaningThe fibre-laser beam selectively vaporises the rust, paint or resin layer — precise ablation, with low impact on the metal substrate; the effect depends on material and parameters.Rust, paint, oxides, release agents, burnt resins — layer by layer, with precisionInefficient on bulk grease and biological soiling; the highest upfront investmentDry — no water and no abrasive media; running cost: power plus, periodically, the protective lens and extraction filtersLow per hour (power and, periodically, the protective lens and extraction filters) — but high initial investment
Abrasive blastingAbrasive media projected at high pressure mechanically strips the layers — a fast method on large, rough surfaces.Thick rust, multi-layer paint, mill scale, hard deposits — on structural steel, stone, façadesAbrasive by definition — ruled out on delicate surfaces, food zones and precision partsDry, but with dust and spent media to collect and dispose ofMedium — abrasive media is a consumable, plus dust management
High-pressure waterThe high-pressure water jet washes mechanically — on boiler models, hot water also cuts exterior grease.Mud, algae, outdoor grime, deposits on vehicle fleets, halls, façades, floorsWet by definition — the remaining water rules out electrical zones, drainless interiors and the dry HACCP stepWet — plenty of water to drain; the surface needs drying timeLow to medium — water plus power or diesel
Ultrasonic (immersion)Cavitation at 28 kHz makes microbubbles implode on every wetted surface — cleaning internal channels no jet can reach, provided the cleaning liquid can reach the area.Carbon deposits, grease, varnish, residues from injectors, carburettors, machined parts, filtersOnly what fits the tank and tolerates immersion — batch cleaning, not fixed surfacesWet, but in a closed bath — the part comes out clean, the solution gets filteredLow — bath and power; it works alone, no dedicated operator

Straight to the demo request ↓

Each technology in detail

High-temperature dry steam

Heat loosens grease and can support hygiene-critical cleaning; the result depends on the temperature actually reached at the surface, the exposure time and the contamination — not on a nominal machine figure.

Choose it when

  • Daily HACCP sanitation in food production or HoReCa, with fewer disinfection chemicals
  • Degreasing equipment, hoods and conveyor belts — no rinsing step
  • Recurring mould in damp zones: thermal treatment of the surface, which stays almost dry
  • Auto detailing, upholstery, interiors — gentle steam at regulated pressure

Do NOT choose it when

  • Rust or paint to remove — that is laser or abrasive-blasting territory
  • Electrical cabinets and equipment — water and steam do not belong there; dry ice may be considered for some electrical applications after an electrical safety review
  • Parts with clogged internal channels — ultrasonic baths clean where no jet reaches

Pressure and steam output tell you how capable the machine is, not what hygiene result you will achieve. That is validated on the real surface, under your own working conditions.

Real parameters

Working pressure
4–20 bar, depending on model
Steam output
depends on the model and the number of operators
Water and condensate
depends on machine, accessory and surface
What decides the result
temperature reached at the surface, exposure time, distance, accessory and contamination

Dry ice (CO₂)

CO₂ pellets at -78.5 °C detach deposits by thermal shock, then sublimate — straight to gas, no water as the cleaning medium and no secondary abrasive medium; the effect on the surface depends on material, contamination and working parameters.

Choose it when

  • Electrical cabinets, motors, automation — a dry process without water; on energised equipment only after a site-specific electrical safety review, under the equipment manufacturer's procedures and with qualified personnel
  • Cleaning in place, often without full disassembly of the line
  • Bottling lines and food zones where water or abrasive media are unwanted
  • Surfaces that tolerate no abrasion — the pellet is soft, with low risk to the substrate; test on a sample

Do NOT choose it when

  • Routine daily sanitation — if steam handles the soil, there is no reason to use up pellets
  • Adherent rust or paint — thermal shock will not lift them; choose laser or blasting
  • Night shifts with strict noise limits — the jet and compressor are audible

The real cost is the pellet: 20–80 kg per working hour. That is why high-volume plants produce their own — a pelletiser makes up to 180 kg/h and turns the consumable into your own raw material.

Real parameters

Pellet temperature
-78.5 °C (solid CO₂)
Blasting pressure
1–16 bar, depending on model
Pellet consumption
20–80 kg/h, adjustable
Compressed air
0.5–6.5 m³/min with one hose, depending on model and pressure (up to 13 m³/min with two hoses)

Laser cleaning

The fibre-laser beam selectively vaporises the rust, paint or resin layer — precise ablation, with low impact on the metal substrate; the effect depends on material and parameters.

Choose it when

  • Rust and paint on metal where the substrate must stay untouched
  • Injection moulds: resin and release agents come off on the machine, no dismantling
  • Restoration and precision parts — you control the depth instead of guessing
  • Weld preparation and oxide removal, with no blasting media to manage

Do NOT choose it when

  • Degreasing or biological sanitation — steam does that far more efficiently
  • Large rough areas where speed beats precision — blasting is faster on structural steel
  • Tight budget with occasional use — the investment pays off through regular use

Laser is one of the methods that removes the layer with minimal mechanical contact on the substrate — which is why it wins wherever the part is worth more than the cleaning.

Real parameters

Laser power
1000–3000 W (fibre laser)
Cleaning speed
5–80 m²/h at 1000–2000 W (datasheet), depending on the layer
Scan width
up to 300 mm, adjustable
Consumables
no abrasive; the protective lens and extraction filters are replaced periodically

Abrasive blasting

Abrasive media projected at high pressure mechanically strips the layers — a fast method on large, rough surfaces.

Choose it when

  • Surface preparation before painting or coating on structural steel
  • Thick rust and old multi-layer paint on large surfaces
  • Stone and brick restoration, where the final texture is part of the result
  • Fast and low-cost on raw metal, when the substrate tolerates abrasion

Do NOT choose it when

  • Precision parts or moulds — laser controls the depth, blasting does not
  • Electrical or electronic equipment — media and dust are ruled out there; dry ice may be considered, after a safety review by a technical specialist
  • Food production zones — abrasive media contaminates

Real parameters

Working pressure
up to 10 bar
Media tank
25–200 L, depending on model
Operating temperature
-10 … +50 °C
Consumables
abrasive media (sand, corundum etc.)

High-pressure water

The high-pressure water jet washes mechanically — on boiler models, hot water also cuts exterior grease.

Choose it when

  • Exteriors: façades, platforms, halls, floors with drainage
  • Fleets and commercial vehicles — high volume, high speed
  • Coarse adherent dirt where water volume is an advantage, not a problem
  • With hot water (up to 140 °C): grease and oil on exterior surfaces

Do NOT choose it when

  • Electrical or electronic equipment — water is ruled out; dry ice may be considered, after a safety review by a technical specialist
  • Drainless production interiors — standing water stops the line until it dries
  • HACCP sanitation that needs an immediately dry surface — steam leaves it almost dry

Real parameters

Working pressure
100–280 bar, depending on model
Flow rate
up to 21 l/min
Hot water
up to 140 °C (boiler models)
Power source
electric or diesel

Ultrasonic (immersion)

Cavitation at 28 kHz makes microbubbles implode on every wetted surface — cleaning internal channels no jet can reach, provided the cleaning liquid can reach the area.

Choose it when

  • Injectors, carburettors, parts with internal channels — cavitation cleans where brush and jet cannot reach
  • Batches of small or complex parts — the batch cleans itself while you work
  • Auto workshops and maintenance: repeatable results, no manual scrubbing
  • Parts that tolerate no abrasion but tolerate immersion

Do NOT choose it when

  • Fixed installations and large surfaces — they cannot be immersed; choose steam, dry ice or pressure
  • Parts larger than the available tank (though tanks go up to 9,000 L)
  • Materials sensitive to prolonged immersion

It is one of the methods that clean internal geometry — and one of the few that work alone: load the batch, start the bath, get on with your day.

Real parameters

Frequency
28 kHz (40 kHz optional)
Tank capacity
4 – 9,000 litres
Ultrasonic power
up to 32 kW on large tanks
Construction
AISI 304 / 316L stainless steel

The reality: many plants need two technologies

A food plant sanitises daily with steam (minimal operating cost) and may consider dry ice for its electrical cabinets and line, in place, after a safety review by a technical specialist. A reconditioning workshop combines laser for rust with an ultrasonic bath for internal channels. A car service uses steam inside and pressure outside.

That is why the right question is not "which machine do I buy" but "which problem am I solving". Describe your problem — we will tell you honestly which technology (or combination) solves it, and demonstrate it at your site, on your actual dirt.

Frequent questions when choosing the technology

Can steam remove rust?

No. Dry steam loosens grease, oils and organic contamination, but does NOT lift adherent rust — for rust you need laser or abrasive blasting. A more powerful machine does not change that: it is a limit of the method, not of the machine size.

Steam or dry ice — which one for the food industry?

For daily surface sanitation: steam, at minimal operating cost (water and power). For electrical cabinets, motors and cleaning the line often without full disassembly, dry ice can be considered — a dry process without water; on electrical equipment, after a site-specific safety review. Many plants use both — each on its own step.

Laser or blasting for rust?

Laser when the substrate matters: moulds, precision parts, restoration — it removes the layer with little impact on the metal and consumes no media. Blasting when speed on large areas matters: structural steel before painting, at a low cost per square metre. The difference is not "which is better" but what you lose if you get it wrong: with laser you pay for precision, with blasting you accept abrasion.

Which technology cleans entirely without water?

Dry ice (dry, no water; on electrical equipment only after an electrical safety review), laser (dry ablation, no media to manage) and abrasive blasting (dry, but with dust and media to manage). Dry steam is a low-water process: steam condenses when it transfers heat to a cooler surface, and the amount of condensate depends on the machine, accessory, surface and dwell — it is not zero water.

Can I clean electrical cabinets with steam or water?

No. Water and steam are ruled out on electrical components. Dry ice can be considered: CO₂ pellets at -78.5 °C sublimate on contact, without water — often without dismantling. On energised equipment, however, a site-specific electrical safety review, the equipment manufacturer's procedures and qualified personnel decide — not the cleaning method.

Why does pressure matter on a steam machine?

Pressure and steam output show how much energy the machine can deliver and how many operators it can supply — which is why they matter when choosing a machine. On their own they do not tell you what cleaning or hygiene result you will get: that depends on the temperature actually reached at the surface, the exposure time, the distance, the accessory and the contamination. This is why we do not rank steam machines by pressure when hygiene is the question.

What does each technology cost to operate?

Steam: water and power (or diesel). Laser is cheap per hour (power and, periodically, the protective lens and extraction filters) but carries a high initial investment. Dry ice is premium to operate: pellets (20–80 kg/h) are a real consumable — the cost only drops if you produce your own pellets in-house.

I have several problems at once — what now?

That is exactly what this guide is for: most plants need a combination (for example steam for daily sanitation plus dry ice for electrical). Describe your problems and we will propose the right combination, with a demonstration at your site — no inflated list price and no extra technology you do not need.

Tell us the problem — you don’t need to know the technology

Describe what you are cleaning, on which surface and how often. We answer with the right technology (or combination), with real parameters — and demonstrate it at your site, on your dirt.

No price, no obligation. We propose the real technology + an on-site demonstration.